Mô tả

Bộ đổi nguồn tổ ong 36 ~ 72VDC sang 5VDC 30A Leyu SD-150C-5

150W Single Output DC-DC Converter SD-150 series

2:1 wide input range

Protections: Short circuit / Overload / Over voltage

1500VAC I/O isolation

Built-in EMI filter, low ripple noise

100% full load burn-in test

24V and 48V input voltage design refer to LVD

Low cost , High reliability

2 years warranty

Model SD-150A-5 SD-150B-5 SD-150C-5 SD-150B-12 SD-150C-12 SD-150D-12 SD-150B-24 SD-150C-24 SD-150D-24
DC Voltage 5V 12V 24V
Rated Current 30A 12.5A 6.3A
Current Range 0-30A 0 ~ 12.5A 0 ~ 6.3A
Rated Power 150W 150W 151.2W
Ripple & Noise 120mVp-p 120mVp-p 150mVp-p
Voltage Adj. Range 4.5~5.5VDC 11 ~ 16VDC 23 ~ 30VDC
Voltage Tolerance ±1.0% ±1.0% ±1.0%
Line Regulation ±0.5% ±0.5% ±0.3%
Load Regulation ±0.5% ±0.5% ±0.3%
Setup, Rise Time 2s, 50ms at full load
Hold Up Time 24ms(only D mode) at full load
Voltage Range A:9.2~18VDC B:19 ~ 36VDC   C:36 ~ 72VDC   D:72 ~144VDC or 85 ~ 132VAC
Efficiency 70% 73% 76% 75% 77% 79% 77% 80% 82%
Inrush Current D: 22.5A/96VDC
Leakage Current <0.75mA / 120VAC (SD-150D)
Over Load 105 ~ 135% rated output power
Protection type: Hiccup mode, recovers automatically after fault condition is removed
Over Voltage 16.8V ~ 20V/10% LOAD 31.5 ~ 37.5V/10% LOAD
Protection type: Hiccup mode, recovers automatically after fault condition is removed
Working Temp. -10 ~ +60℃ (Refer to “Derating Curve”)
Working Humidity 20 ~ 90% RH non-condensing
Storage Temp., Humidity -20 ~ +85℃, 10 ~ 95% RH
Temp. Coefficient ±0.03%/℃ (0 ~ 50℃)
Vibration 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
Safety Standards IEC60950-1 CB approved by TUV (for D type only)
Withstand Voltage I/P-O/P: 1.5KVAC   I/P-FG: 1.5KVAC   O/P-FG: 0.5KVAC
Isolation Resistance I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃ / 70% RH
EMC Emission Compliance to EN55022 (CISPR22) Class B
EMC Immunity Compliance to EN61000-4-2,3,4,6,8, light industry level, criteria A
Dimension 199*110*50mm (L*W*H)
Weight 0.86Kg
Packing 16pcs/14.5Kg/0.95CUFT
1. All parameters NOT specially mentioned are measured at 24,48,96VDC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance: includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.
Đăng nhập
Đăng ký
Hotline: 0904251826